Key takeaways
- Shop the best bike sawhorses for workshop support, with five folding pairs compared on maker-listed capacity, working height, weight and storage.
Every bike workshop has jobs that happen off the repair stand: truing a wheel on a flat surface, laying out a frame for a careful clean, or building a temporary bench for a second mechanic. The best bike sawhorses handle that supporting work. A pair of folding sawhorses, topped with boards or a sheet of ply, becomes a work surface at a comfortable height in under a minute, then folds flat against the wall when the job is done. As an Amazon Associate, I earn from qualifying purchases.
All five picks below are general workshop products, and this guide treats them that way. No maker sells a sawhorse designed for bicycles, so the buying questions are the workshop ones: how much load the maker lists, how tall the top sits, how the legs fold, and how much each horse weighs. Every capacity figure is a maker or listing figure, quoted exactly as published, because brands present those numbers differently.
A Sawhorse Is A Work Support, Not A Bike Stand
One distinction matters before anything else. A sawhorse does not hold a bicycle up for repair. It has no clamp, no axle mount, and no way to keep a bike upright while you turn the cranks, and no pick here is a substitute for a repair stand. What a sawhorse does well is support everything around the repair: a worktop for tools and parts, a rest for wheels waiting their turn, or a platform for a frame laid on padding during a deep clean.
Used that way, a pair of sawhorses earns permanent space in a workshop. They set up faster than a folding table, store flatter, and shrug off the drips and dropped tools that come with mechanical work. The picks below are all folding steel models sold singly or in pairs, chosen because their listings publish clear load figures.
What To Look For In Workshop Sawhorses
Capacity is the headline figure, and it needs careful reading. Some makers list a figure per single horse, others list a combined figure for a pair, and the two presentations sit side by side in this guide exactly as each listing states them. A pair figure assumes the load is spread evenly across both horses. For workshop support duty, even the lowest figure below is far beyond what frames, wheels, and toolboxes weigh; the higher figures matter when the same horses double up for timber and sheet goods.
Working height decides comfort. Most folding sawhorses put the top somewhere around 30 to 32 inches, a sensible height for working over a laid-out wheel or parts tray without stooping. Adjustable-leg models let you level the top on an uneven garage floor, which is worth having if your floor slopes toward a drain.
Support arms and top design come next. Several picks carry arms that grip a 2×4 on edge, so two horses and two boards become a rigid table frame, and a sheet on top becomes a full workbench. Others keep a plain metal top with slots that hold a board flat. For bike work, the board-gripping designs are the most useful, because a stable ply top is where truing stands, parts trays, and cleaning bowls actually live.
Finally, weigh the pair and check the fold. Horses in a home workshop get moved constantly, pushed aside for the car or carried outside for a wash-day setup. A light pair with a flat fold gets used; a heavy pair that stores awkwardly quietly becomes furniture. Non-skid feet matter too, because a horse that creeps across smooth concrete under a leaning load is worse than useless.
1. ToughBuilt C700 Sawhorse And Jobsite Table, 2-Pack
The C700 is the heavy-duty end of this lineup. ToughBuilt builds it from alloy steel, and the maker’s manual lists a capacity of 1,300 lb for each sawhorse and 2,600 lb for the pair, the highest figures in this guide as published. That headroom means a thick worktop, a full parts bin, and a mechanic leaning on the edge all stay comfortably inside the maker’s number.
The support arms adjust to hold material up to 4×4 size, so the pair takes two boards on edge and turns into a rigid jobsite table frame in moments. Add a sheet of ply and you have a bench-height surface for a truing stand or a complete build layout, then fold everything flat when the car needs its space back. Sold as a two-pack under the model TB-C700-2, it is the pick for a permanent two-horse setup.
Specs
- Pack: 2 sawhorses
- Model: TB-C700-2
- Construction: alloy steel
- Load capacity: 1,300 lb per sawhorse, 2,600 lb per pair, as listed by the maker
- Support arms: adjustable, holds material up to 4×4 size
- Converts to a jobsite table with boards in the arms
- Legs fold for storage
2. Bora Speedhorse, 2-Pack
The Speedhorse is built around setup speed. Its legs fold out and lock in seconds, with no loose parts to align, so a work surface appears almost as fast as you can unfold the pair. Bora lists a capacity of 1,500 lb for the model, and the working height is 31.5 inches, squarely in the comfortable zone for working over a bench top.
The metal top is 45 inches long and 3.25 inches wide, with slots that hold a 2×4 flat, so a board laid across the pair stays put while you work. At 17.9 lb per horse, the Speedhorse is not the lightest pick here, but that weight buys a solid, planted feel. Sold as a two-pack under the model PM-4500T, it suits riders who set up and pack away a temporary workstation often, such as a shared garage or a pit area at an event.
Specs
- Pack: 2 sawhorses
- Model: PM-4500T
- Load capacity: 1,500 lb, as listed by the maker
- Working height: 31.5 inches
- Top: 45 inches long x 3.25 inches wide, metal, with 2×4 slots
- Weight: 17.9 lb per sawhorse
- Legs fold out for fast setup
3. ToughBuilt C550 Sawhorse And Jobsite Table, 2-Pack
The C550 is the C700’s smaller stablemate, and for many home workshops it is the better fit. The listing gives a combined load capacity of 2,200 lb for the pair, which works out at 1,100 lb per horse, and the frame is all steel with a powder-coated finish. That is still far more support than any bike job asks for, in a pair that lists at 26.24 lb all-in.
Adjustable 2×4 support arms let the pair become a jobsite table, the same trick as the C700, so a board-and-sheet top is always an option when a job outgrows the floor. The folding design keeps storage simple: legs tuck in, and the pair leans flat against a wall or slides under a bench. If the C700 is the permanent heavy setup, the C550, sold as a two-pack under the model TB-C550-2, is the lighter pair you will actually carry outside for wash day.
Specs
- Pack: 2 sawhorses
- Model: TB-C550-2
- Load capacity: 2,200 lb combined per pair, as listed
- Frame: all steel, powder-coated finish
- Support arms: adjustable, holds 2×4 boards
- Converts to a jobsite table with boards in the arms
- Weight: 26.24 lb for the 2-pack, as listed
- Legs fold for storage
4. BORA Workhorse XT, Single
The Workhorse XT answers the uneven-floor problem. Its legs adjust in height, so the top can sit level on a sloping garage slab or a rough driveway, rather than shimming feet with cardboard. Bora lists a capacity of 1,350 lb for the model, and the listing even notes a built-in bottle opener on the frame.
Because it is sold singly under the model PM-3360, the Workhorse XT is the flexible way to build a setup: one horse pairs with an existing bench for a long worktop, or two singles give you a matched, height-adjustable pair. For bike work, the levelling matters more than the headline capacity, since a wobbling surface is where small parts roll away.
Specs
- Pack: 1 sawhorse
- Model: PM-3360
- Load capacity: 1,350 lb, as listed
- Legs: adjustable height, folding
- Built-in bottle opener, per the listing
5. CRAFTSMAN Metal Sawhorse, Single
The CRAFTSMAN is the light, simple option. The listing-derived figures give a capacity of 1,000 lb per pair and an item weight of just 5.69 lb, so a single horse is an easy one-hand carry and a pair is no burden at all. Anti-slip rubber pads on the feet help it stay planted on smooth floors, and side latches let two horses stack and carry together.
There are no support arms or table conversions here, and that is the point: this is a plain folding metal sawhorse for quick support jobs, holding a worktop board, a wheel set, or a parts tray at working height. Sold singly under the model CMST11154, it suits a small workshop where storage is tight and the horses come out for one job at a time. Buy two for the full worktop setup, since the pair figure is the one the listing quotes.
Specs
- Pack: 1 sawhorse
- Model: CMST11154
- Load capacity: 1,000 lb per pair, as listed
- Weight: 5.69 lb
- Feet: anti-slip rubber pads
- Side latches for stacking
- Legs: folding metal
Using Sawhorses Safely In A Bike Workshop
Treat a sawhorse like any other support: open the legs fully and make sure braces and locks are seated before anything goes on top, and set the pair on flat, dry ground. Never stand on a sawhorse or on a worktop resting on one; the makers’ manuals are blunt on that point, and a worktop is a surface for parts, not people. Spread loads evenly between the two horses, and keep the total, worktop included, inside the maker’s listed figure for the pair.
Around bikes, add padding where painted tubes meet metal. A folded towel or foam pad between a frame and a steel top prevents the small chips that bare metal causes, and it stops round tubes rolling.
Frequently Asked Questions
Can a sawhorse replace a bike repair stand?
No. A sawhorse has no clamp and no way to hold a bike upright or lift a wheel off the ground, so it cannot do a repair stand’s job. It supports the work around the repair instead: worktops, wheels waiting for attention, frames laid on padding, and parts laid out in order. Most workshops end up wanting both.
How much weight can a pair of sawhorses hold in a workshop?
Only as much as the maker lists, and the listings present the figure differently: some quote a capacity per single horse, others quote a combined figure for a pair, and this guide repeats each number exactly as published. Pair figures assume an evenly spread load. For bike work the loads are modest, a worktop, tools, wheels, and parts, so any pick here has ample headroom when used as the maker describes.
Is one sawhorse enough, or do I need a pair?
A pair is the useful setup for a worktop, because a board or sheet needs support at both ends. A single horse still earns its keep against a bench or wall ledge, holding the free end of a long board or a second worktop at matching height. Two of the picks here are sold as pairs, and the singles let you start with one and add a second later.
What should go between a frame and a steel sawhorse top?
Padding, always. Bare steel against a painted or carbon tube risks chips and scratches, and a round tube on a narrow metal top can roll. A folded towel, a foam pad, or a rubber mat gives grip and protection. When the job is a full clean or a parts layout, a sheet of ply across two horses with a mat on top is the most forgiving surface in the workshop.
FAQ
Can a sawhorse replace a bike repair stand?
How much weight can a pair of sawhorses hold in a workshop?
Is one sawhorse enough, or do I need a pair?
What should go between a frame and a steel sawhorse top?
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialA Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.
See Prime for Young AdultsAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.